7 Warm White LED wired lighting set; 5 Opal Fixtures, 2 Snap in coach LEDs NEW

Description

New Item for 2016 at a special introductory price while stock lasts
G Scale SL-8207230 7 Warm White LED Prewired Lighting set; 5 Tiffany Opal White Fixtures &
2 Snap in
LEDs for LGB coach lamps
Ready to run;
prewired easy to install lighting for LGB center copula caboose
Shourt Line Product Number: No.
SL-8207230
prewired ready to install
Requires SL LED controller sold separately
Direct From Manufacturer-
Made in the USA
This photo shows th
is item, the
SL-8207230
7 LED set and 1
SL-8291230
LED Tiffany Opal Lamp Fixture, not included with this set, mounted on the exterior platform ceiling.
(The
SL-8291230
LED Tiffany Opal Lamp Fixture on exterior platform, LGB Car, Track and Figures are also not included with the set.)
The prewired
SL-8207230
7 LED set
installs in minutes to any center copula caboose with included mounting screws and 3M peel mounting pads that mounted on the 3 interior single LED fixtures and two mounted LEDs on SL plugs that snap into LGB exterior lamps.
(The
2 each
SL-8291230
LED Tiffany Opal Lamp Fixtures on the exterior platforms,
SL LED controller, Anti-flicker buffer,
LGB Car, and Track are not included with the set.
)
Click here for more product details and larger photos
Buy it now Price:
.95
New
Description:
This new, easy to use 7 LED prewired Tiffany style white opal lamp fixture includes 4 stainless screws and peel-and-stick 3M mounting pads for the center copula fixture and 2 Snap in LEDs for LGB coach lamps. It includes 5 Tiffany style opal lamp shades for prototypical appearance and 2 snap in LEDs pre-wired for LGB exterior coach fixtures.
This set requires the use of a Shourt Line LED controller for safe and efficient operation. The set uses parallel wiring for LEDs and allow additional LEDs, up to 300, to be wired in parallel to an SL LED controller. The SL LED controllers are available with solder and screw type terminals for mounting on car wall, ceiling or under G Scale short or long cars.
The SL LED controller is up to 94% efficient so that even the LGB starter set power pack will power a loco, its lights and 12 LED lamps plus additional car lighting for future expansion. The newest SL LED controller is unique in operating at 1/6th the power of any other available and it also works at the lowest track voltage or no track voltage, it fact it operates 8 LEDs up to 5 minutes without any track power!
F
eatures:
SL-82913230
High Output
Warm White LED color for matching bulb color temperature
Warm Warm White (WWW) and Yellow Warm White (YWW) color also available on request.
Opal Lamp shade for diffused lighting
Prototypical Appearance
4 Stainless Screws for mounting the 2 each prewired dual white opal LED fixtures
3M Peel and Stick Installation pad is included on the prewired center cupola fixture
Hidden wiring on the 2 dual white opal LED fixtures
White Opal LED Lamp Shade Dimensions:
Lamp diameter: 16mm (1.1")
Fixture height:
20mm (.78")
Default color temperature is Warm White which is matched for 3,200 degrees Kelvin that matches LGB two pin bulbs in color temperature. Use the Incandescent setting on your camera from proper color temperature in your photos.
At the time of order you can request the Yellow Warm White or the Warm Warm White but we recommend using the Warm White standard unless you want to simulate a yellow outdoor bug light (YWW) or candle flame (WWW) see the photos below to compare.
You will receive the recommended Warm White LED lamp fixture shown on the right side of the photo above unless you request the WWW or the YWW color temperature LEDS with your order.
This photo shown the right angle SL 1 LED Tiffany style Opal Lamp fixture with simulated wood mounting bracket. Note the difference in color temperature in the pools of light from each fixture. The Warm White is recommended but the other color temperatures are available upon request as the time of ordering.
Instructions:
The photos shown below are for examples of use, wiring and placement of the set that includes; 2 pre-wired dual Opal LED fixtures, 1 single Opal LED fixture and
2 snap in LEDs pre-wired for LGB exterior coach fixtures
.
This set requires an SL LED controller for safe and efficient operation. We install lighting products an all makes of G scale cars if you do not want to do the install yourself. The 7 LED set takes only minutes and a screw driver to install. SL LED controllers are available in both solder and screw terminal types. We will set up the controller of your choice when requested so you do not have to adjust the voltage per the instructions that comes with each controller. A volt/amp meter is required to set the safe operating voltage on our SL LED controllers. Other makes and models of controllers may not work with direct parallel wiring of LEDs. If you want to use another controller be sure to use dropping resistors on each LED as they usually will not provide proper operation without them. All our controller work by parallel wiring LEDs without the use of dropping resistors.
Adjust your SL Lighting controller using the instructions provided with your controller
(not included with this set)
Do not use a voltage above 3.1 volts
Test the fixture
by connecting the black lead with ridges to the (-) negative output and the smooth black lead to the (+) positive output of a SL LED controller
AFTER
it has been set to the proper voltage
.
Check to see that all lamps turn on, if not reverse the leads and retest, the black conductor (wire) that has ridges on the cover is the negative lead, the smooth wire is the positive lead.
If the lamps fail to light contract us at the ShourtLine.com
Wire the positive lead to the positive output of the SL LED controller. Do the same for the negative (ridged wire) by wiring to the negative output.
Screw the two dual lamp fixtures with the included 4 stainless steel screws.
Clean the surface
where you want to mount the single light fixture in the center of the copula ceiling (see photo above) with an alcohol wipe
Peel off the read tape to reveal the 3M adhesive pad
(see photo below)
Hold the fixture above the mounting surface to check the correct position
before it touches the mounting surface
.
Apply gentle pressure by pushing on the LED.
Route the wires as shown above to your choice of SL LED controller.
Wire the SL LED controller to a source of power, such as 1 each PIKO ball bearing power pickup axle, an SL power pickup up kit, a battery (9 volt battery works well) or to a loco or car that has power.
Optionally use an anti-flicker buffer as shown above.
Use only with an SL LED controller
; damage to your led fixture is not covered with other controllers or if instructions are not followed.
The center copula fixture comes with pre-wired micro cable leads for easy installation. You lighting fixtures will provide a wide angle illumination as shown above.
To install, clean the surface you want to mount to with an alcohol wipe, peel off the read tape to reveal the 3M adhesive pad and apply.
To wire extra
SL-8291230
fixtures to the exterior porch ceiling, wire the long lead to the LEDs marked + on the two LED fixtures by soldering but test first to be sure you have the correct polarity. The set comes 5 interior LED fixtures, 2 coach plug and play LEDs but does not come with the exterior center porch LEDs shown above.
(The
2 each
SL-8291230
LED Tiffany Opal Lamp Fixtures on the exterior platforms,
SL LED controller, Anti-flicker buffer,
LGB Car, and Track are not included with the set.
The prewired
SL-8207230
7 LED set
show above is controlled and wired to an
SL-8453003
Precision Train Throttle & LED controller
(not included with the set) that has
SL-7453003
3 side snap-on cover (not included with the set).
(The
LED controller case,
2 each
SL-8291230
LED Tiffany Opal Lamp Fixtures, SL LED controller, Anti-flicker buffer, LGB Car, and Track are not included with the set.
)
The SL LED controller above is recommended but not included with this 7 LED set
To power from AC DC or DCC track power use the Shourt Line
SL-8453003
Precision Train Throttle & LED controller
(shown above)
. The controller can power and dim over 300 LEDs at up to 94% efficiency from AC,DC or DCC at 4 to 35 volts. It uses 1/6 the power of all other lighting systems available.
It is easy to wire this 7 LED set to an SL LED controller as shown above or to an existing SL LED fixture by wiring in parallel, + to + and - to -. No dropping resistors or complicated formulas
are needed
. Up to 300 LEDs can be powered from each SL LED controller.
Photo
s:
The exterior
SL-8291230
LED Tiffany Opal Lamp Fixtures, track, caboose and fixtures are not included
.
The exterior
SL-8291230
LED Tiffany Opal Lamp Fixtures, track, caboose and
figures
are not included
.
Don't leave your passengers in the dark, install this set in your caboose for prototypical lighting.
Click here for more product details and larger photos
Questions? Phone 310-622-4431
Thanks for looking - ShourtLine.com by Soft Works Ltd.
copyright 2016 Shourt Line - Soft Works Ltd. all rights reserved